Новый ISPSoft 3

nerokeygen
Сообщения: 1
Зарегистрирован: 24 июн 2019, 23:07

Re: Новый ISPSoft 3

Сообщение nerokeygen »

если будет огроммный кривой путь установки то и не поставится
еще там проблемы с русским
к примеру не работает монитор определенных переменных
кой чего не переведено
ну и кракозякбры кой где...
пересобрал инсталлятор испишки
с измененными файлами русского
ну и повыкидал остальные языки
делал для себя
так как по работе на нем и сижу
wpl за оболочку не считаю
мои проги запаришся на нем писать

and909
Сообщения: 858
Зарегистрирован: 28 май 2013, 13:20

Re: Новый ISPSoft 3

Сообщение and909 »

Круто.
Я тут уже спрашивал: как можно поменять шрифт на Ариал, сразу везде, чтобы не лазать по настройкам?

Алексей29
Сообщения: 113
Зарегистрирован: 17 дек 2020, 12:28
Откуда: Воронеж

Re: Новый ISPSoft 3

Сообщение Алексей29 »

проблема была в другом.
винда заблокировала файл .
жмём ПКМ, свойства и видим - этот файл был скачан из интернета и заблокирован в целях безопасности.
ставим галку - разблокировать и усё.

prolex888
Сообщения: 7
Зарегистрирован: 07 июн 2022, 14:19

Re: Новый ISPSoft 3

Сообщение prolex888 »

Народ, кто-нибудь уже пробовал подключать что-нибудь по MQTT-протоколу? Работает ли, какие ньюансы?

and909
Сообщения: 858
Зарегистрирован: 28 май 2013, 13:20

Re: Новый ISPSoft 3

Сообщение and909 »

Сегодня пытался использовать инструкцию ATMR на AS300, столкнулся с ошибками, разбирался и выяснил:
1. Инструкция ATMR API1016 заработала на контроллерах AS с новой прошивкой V1.12, так что обновитесь.
2. Инструкцию ATMR в симуляторе пока не допилили (ждем новый COMMGR)
3. Встроенной справки в ISPSoft по F1 для ATMR не выходит (качайте свежий мануал).

На реальном ПЛК после обновления прошивки замечаний по работе ATMR не обнаружено.

bayk
Сообщения: 887
Зарегистрирован: 30 май 2015, 21:20

Re: Новый ISPSoft 3

Сообщение bayk »

с твоего позволения перенесу в тему по программированию AS

and909
Сообщения: 858
Зарегистрирован: 28 май 2013, 13:20

Re: Новый ISPSoft 3

Сообщение and909 »

Вышла новая версия:

Version: 3.17
Date of Publication: Feb. 24, 2023
1. ISPSoft V3.17 now supports DVP-EC5.
2. EtherCAT adds a new funciton “Hot Connect Group” for users to configure EhterCAT Slaves in a more flexible way.
3. Four modes are added in the Positioning Settings: Relative Mode (Symbol / Target Position & Speed), Absolute Mode ((Symbol / Target Position & Speed), Relative Mode (Symbol / Target Position & Velocity & ACC & DEC Time) and Absolute Mode (Symbol / Target Position & Velocity & ACC & DEC Time).
4. Optimized online editing for DVP Series.
After each online editing, the source code will be downloaded automatically to the PLC to ensure that the source code and the updated execution code will be consistent.
Previous versions: After online editing, a prompt message will remind you to download the program.
V3.17 and later versions: The source code will be downloaded to the PLC automatically after each online editing.
5. Newly added instructions.
Instruction:
DWSFR, DWSFL, DSFWR, DSFRD, DSFPO, DSFDEL, DSFINS, DSFR, DSFL, DNSFR, DNSFL, BK*, BK/, BKF+, BKF-, BKF*, BKF/, BKMUL16, BKMUL32, BKDIV16, BKDIV32
6. Updated function for Card Utility
a. AH5x1 / AH560: added a new item “COM Delay to send” in the Backup setting section.
b. Added a new supported model, DVP-EC5. Select Controller Type to DVP and then you can find EC5 from the drop-down list of PLC Type.
7. The following issues are fixed and functions are modified:
(1) Fixed an issue that after the AHEMC Series PLC downloaded the hardware configurations, the COM port cannot function normally.
(2) Fixed an issue that when AH Series PLC executes mapping on the device Ds, if the number of devices exceeding the limit, no error shows.
(3) When executing “download” in EtherCAT, user privileges play no part in this operation.
(4) Ease the format checks for the ESI file before importing, for instance, the date format and the LCID format.
(5) Fixed an issue that if there are more than one port in one adapter in EtherNet/IP, the indications of the ports will be shown overlapped in the topology.
(6) Fixed an issue that if using Data Unit Type (DUT) as a pin in a function block within a function block, a compilation error will occur.
(7) Fixed an issue that if an ES3 Series PLC monitors the register Y in ST language, the monitoring results will be incorrect.
(8) Fixed an issue that if a DVP Series PLC uses step positioning to jump to a specific step in the function block, a message that shows this function is not supported will appear.
(9) Fixed an issue that after changing the order of the symbols, it does NOT trigger ISPSoft to compile the project again and this may bring incorrect monitoring results.
(10) Fixed an issue that when using a HC register as a pin for a 32-bit comparison instruction, a compilation error may occur.
(11) Fixed an issue that if executing “monitor” in ST language, some misjudgments on the string contents may occur and the monitoring results will be incorrect.
(12) Fixed an issue that after the execution of symbol-replacing, some symbol names in the symbol table will be replaced with the illegal symbol names.
(13) Type “TIMER” can support using ST registers in the field of address for AS Series PLC in the Main Table.
(14) Fixed an issue that if the value used in the target position of the positioning table is negative, an error message will appear.
(15) Modify the rules in IntelliSense (a code-completion aid). When entering “???” or leave the field blank in the field of symbol name, no symbol names will show up.
(16) Fixed an issue that when DVP Series PLC uploads a project, sometimes an unrelated and incorrect error message will show up “Current PLC firmware version does not support this function. Please update the firmware version to X.XX or above.”
(17) Turkish is added in the language settings for selection.

and909
Сообщения: 858
Зарегистрирован: 28 май 2013, 13:20

Re: Новый ISPSoft 3

Сообщение and909 »

Мне кажется, самое полезное вот это:
4. Optimized online editing for DVP Series.
After each online editing, the source code will be downloaded automatically to the PLC to ensure that the source code and the updated execution code will be consistent.
Previous versions: After online editing, a prompt message will remind you to download the program.
V3.17 and later versions: The source code will be downloaded to the PLC automatically after each online editing.

Aeroplan
Сообщения: 289
Зарегистрирован: 17 окт 2013, 11:39
Откуда: Санкт-Петербург

Re: Новый ISPSoft 3

Сообщение Aeroplan »

А мне 9й пункт больше нравится

and909
Сообщения: 858
Зарегистрирован: 28 май 2013, 13:20

Re: Новый ISPSoft 3

Сообщение and909 »

Version: 3.18

Date of Publication: Aug. 02, 2023

1. The motion control related functions are available for DVP-ES3.
 Axis parameters
(1) When creating a new project, a fixed and uneditable axis parameter node will be automatically generated.
(2) Axis parameters can be uploaded and downloaded.
 E-CAM
(1) Polynomial CAM curve editing function is available. There is no need to set the resolution, and up to 36 key points can be added on a single chart.
(2) The numbers of the position indicator for the main axis or the secondary axis is always rounded to the nearest integer.
(3) E-CAM parameters can be uploaded and downloaded.
2. Added connection information for DVP Series PLC.
You can find the information concerning BaudRate, DataBits, Parity, and StopBits under the PLC Settings.
3. A syntax that omits pin and parameters when calling a function block in ST programming language is supported.
4. Newly added instructions
LDIP
LDIF
ANIP
ANIF
ORIP
ORIF
MC_CAMIN
MC_CAMOUT
MC_STOP
MC_HALT
CAM_READ
CAM_WRITE
CAM_ADJUST
CAM_CHANGE
CAM_VIRTUAL
CAM_ALIGNMENT
CAM_CUTCHECK
CAM_STATUS
CAM_OBJECTDETECT
APF_ROTARYCUT_INIT
APF_ROTARYCUT_STOP
SCMRS
5. Updated function for Card Utility
a. AH5x1 / AH560: added two new items “EIP Tag” and “RTU IO Configuration Table” in the Backup and Restore setting sections.
b. Added a new controller type “VFD” and two models VFD-MH300, VFD-MS300 are supported.
6. The following issues are fixed and functions are modified:
(1) Fixed an issue that if there are declared function blocks in the global symbol table of DVP Series PLC, that would cause contents in the device usage status table to be displayed incorrectly.
(2) Fixed an issue that errors would occur when reading certain segments of D registers in the VFD series model's register editing table.
(3) Optimized the editing experience in the device comment list; when pressing Del button, only the comments of the selected device will be deleted, not the device itself.
(4) Optimized the editing experience in the device comment list; now up to 1000 devices can be used when setting up the quantity of device in adding new devices.
(5) Optimized online edit for DVP Series PLC; a more detailed notice will be prompted to remind you about the update, when the firmware of the PLC you are using is an older one. New notice: About to online edit. (This firmware version only supports execution code update and does not support project program update.)
(6) After specifying a register in the symbol window, if a conflict occurs, a more detailed message will be prompted to inform you. New message: Device XXXX is used by OOOO. Please refer to PPPP for details.
* XXXX indicates the device name.
* OOOO indicates the symbol name.
* PPPP indicates the symbol table name.

Ответить